MSO4000/DPO4000

Серия MSO/DPO4000B заменяется серией MDO4000C. MDO4000C может быть сконфигурирован как осциллограф с цифровым люминофором (DPO) или как осциллограф смешанных сигналов (MSO) в зависимости от области применения.
Подробнее о серии MDO4000C.

Многофункциональные приборы для отладки систем со смешанными сигналами.

Осциллографы смешанных сигналов серии MSO/DPO4000B с полосой пропускания до 1 ГГц и частотой дискретизации 5 Гвыб/с обладают производительностью для изучения быстро изменяющихся особенностей сигнала. Пользуясь 20 каналами, можно анализировать аналоговые и цифровые сигналы при помощи одного прибора. В сочетании с автоматическим анализом последовательных и параллельных шин, инновационными органами управления Wave Inspector® и автоматическим измерением мощности осциллографы серии MSO/DPO4000B обладают необходимыми функциями для отладки аппаратуры со сложными смешанными сигналами.

Нужны приборы серии MSO4000B с полосой пропускания 100 МГц, 350 МГц, 500 МГц или 1 ГГц? Их могут полностью заменить приборы серии MDO4000B. Эти осциллографы оснащены встроенными анализаторами спектра, который включён в стоимость прибора. Узнайте больше об этих приборах .

Features

Benefits

2 or 4 analog and 16 digital channels Analyze analog and digital signals on a single instrument for system-level troubleshooting of complex designs.
Digital phosphor display Quickly discover glitches and infrequent events with a greater than 340,000 wfm/s waveform capture rate and intensity-graded display.
Complete set of triggers Rapidly capture signal anomalies with over 125 available trigger combinations, including setup/hold, serial packet content and parallel data.
Wave Inspector® controls Easily search, mark and navigate long record lengths to find all occurrences of your event.
Automated Measurements Simplify analysis of your device with 42 automated measurements, FFT analysis, measurement statistics, waveform histograms, and advanced waveform math.
Parallel bus triggering and analysis (MSO Series) Quickly debug your parallel bus with automated trigger, decode and search. Capture fast transitions with timing resolution up to 60.6 ps.
Serial triggering and analysis (optional) Quickly debug common serial buses with automated trigger, decode and search – I2C, SPI, USB, Ethernet, CAN, LIN, FlexRay, RS-232/422/485/UART, I2S/LJ/RJ/TDM, and MIL-STD-1553.
Power analysis (optional) Achieve fast, accurate results with integrated automated power measurements.
Low-capacitance passive voltage probing Four probes with industry-best 4pF capacitive loading and up to 1 GHz bandwidth are included standard to ensure accurate measurements

 

Принадлежность ACD4000B
Техническое описание Описание
Просмотр Техническое описание сумка для транспортировки
Принадлежность HCTEK54
Техническое описание Описание
Просмотр Техническое описание Жесткий кейс для транспортировки
Принадлежность NEX-HD2HEADER
Техническое описание Описание
Просмотр Техническое описание АДАПТЕР NEXUS TECHNOLOGY, INC. MICTOR — ШТЫРЬКОВЫЙ РАЗЪЕМ ГОЛОВКИ
Принадлежность RMD5000
Техническое описание Описание
Просмотр Техническое описание Набор для монтажа в стойку
Принадлежность TPA-BNC
Техническое описание Описание
Адаптер пробника TekProbe-BNC — TekVPI
Техническое описание Принадлежность Описание
ACD4000B сумка для транспортировки
HCTEK54 Жесткий кейс для транспортировки
NEX-HD2HEADER АДАПТЕР NEXUS TECHNOLOGY, INC. MICTOR — ШТЫРЬКОВЫЙ РАЗЪЕМ ГОЛОВКИ
RMD5000 Набор для монтажа в стойку
Просмотр Техническое описание TPA-BNC Адаптер пробника TekProbe-BNC — TekVPI
Техническое описание Пакет программного обеспечения/программное обеспечение по дополнительному заказу Описание Конфигурация и ценовое предложение

Gold Care

 
Data Sheet Plan Description Shop Online or Learn More
View Datasheet G3

Gold Care Service  – 3 Years (Expedited repair for all product failures, access to loaner, priority customer service)

Learn More
View Datasheet G5

Gold Care Service – 5 Years (Expedited repair for all product failures, access to loaner, priority customer service)

Learn More

Silver Care (Extended Warranty)

 
Data Sheet Plan Description Shop Online or Learn More
View Datasheet R5

Silver Care Repair Service – 5 Years (Includes warranty)

Learn More
View Datasheet SILV600

Silver Care Repair Service Package – 5 Years (Includes warranty)

Learn More

Calibration

 
Data Sheet Plan Description Shop Online or Learn More
View Datasheet C3

Calibration Service – 3 Years

Learn More
View Datasheet C5

Calibration Service – 5 Years

Learn More

 

KickStart Instrument Control Software Version 2.2.1 (Windows 10, 8, 7 compatible)
KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the ability to …

Номер по каталогу: KICKSTART-2.2.1
Application (Предварительные установки > Приложение)
How do I set up a CAN bus decode?
Depending on what scope you have will depend on what options are availiable for decoding your CAN signal. For all the DPO/MSO2000/3000/4000/5000 and MDO3000/4000 Series scopes there are modules or license keys that can be purchased. Once you have one …
Идентификатор часто задаваемых вопросов64751
Do you have a detailed application note on how to use DPO/MSO4000B Series Oscilloscopes for debugging embedded systems+ serial signals+ power designs+ and general purpose design applications?
Please see the MSO4000B / DPO4000B Series Lab Exercise Book for more details. This lab manual states many walk through labs that will help you under many aspects of how to use the oscilloscopes. Just download the attached lab manual.   Note: Many …
Идентификатор часто задаваемых вопросов58161
What are the primary differences between the DPO/MSO4000B, MDO4000, MDO4000B, and MDO4000C?
The 4000 Series Mixed Domain Oscilloscopes (MDO) continues to be the only true RF/Time domain syncronized instrument on the market. The major differences between revisions of the DPO/MSO/MDO4000 Series are described below. Please note the MDO4000C …
Идентификатор часто задаваемых вопросов72111
Can active probes with TekProbe interface (such as a P6205) be used on the DPO4000B or MSO4000B series scopes?
Yes. A TPA-BNC adaptor is required for people to connect legacy TekProbe interface probes to the new TekVPI interface. The adapter works on any TekVPI scopes inlcuding the MSO/DPO/MDO4000/B/C, MSO/DPO/MDO3000 MSO/DPO2000/B or MSO/DPO5000/B or …
Идентификатор часто задаваемых вопросов60416
What feature does the DPO4BND included?
DPO4BND includes the features for the following modules …
Идентификатор часто задаваемых вопросов72101
When should I run SPC?
Signal Path Compensation (SPC) can be run at any time. The best times to run SPC are: After the oscilloscope has been powered on and has warmed up for 20 minutes or more. If the temperature has changed more than 5 degrees C since the last SPC was …
Идентификатор часто задаваемых вопросов60156
How do I run a Signal Path Compensation (SPC) on an DPO/MSO/MDO4000 Series oscilloscope?
Signal Path Compensation (SPC) should be run anytime you are getting DC offsets in your signals, or your scope has moved locations and might have changed temperature, or if it's been more then a month since your last SPC. This is a standard procedure …
Идентификатор часто задаваемых вопросов64681
How do I set up a I2C Bus Decode?
The procedure to set up a I2C bus decode and trigger is simple once you understand the basics. First you have to have the correct module or scope option. Second make sure your signal is on screen and taking up as much of the DAC as possible with good …
Идентификатор часто задаваемых вопросов64756
What is the maximum bit rate a decoded SPI bus can trigger on?
Different oscilloscopes have different triggering circuitry therefor the limits of what speeds can be achieved vary by scope. Please use the following table to easily look up your scope and determine your max SPI bus trigger level.  For more …
Идентификатор часто задаваемых вопросов62256
Are the DPO2AUTO+ DPO2COMP+ and DPO2EMBD Application Modules licensed to a specific MSO2000 or DPO2000 Series oscilloscope serial number? Are the DPO3AERO+ DPO3AUDIO+ DPO3AUTO+ DPO3COMP+ DPO3EMBD+ DPO3FLEX+ DPO3PWR+ and DPO3VID Application Modules licensed to a specific MSO3000 or DPO3000 Series oscilloscope serial number? Are the DPO4AERO+ DPO4AUDIO+ DPO4AUTO+ DPO4AUTOMAX+ DPO4COMP+ DPO4EMBD+ DPO4ENET+ DPO4USB+ DPO4LMT+ DPO4PWR+ MDO4TRIG+ and DPO4VID Application Modules licensed to a specific MDO4000, MSO4000 or DPO4000 Series oscilloscope serial number?
The application modules are not licensed to a specific oscilloscope serial number and can be swapped between the various models within the oscilloscope series.
Идентификатор часто задаваемых вопросов55201
Can my oscilloscope operate on 400Hz power?
Most scopes have a wide range of operating voltages and frequencies, a full list can be found in the user manual of your specific oscilloscope. If you're having trouble finding your answer or can't find the manual, please call our Technical Support …
Идентификатор часто задаваемых вопросов63266
What is SPC?
SPC is the acronym for Signal Path Compensation. SPC's.  Running Signal Path Compensation corrects for DC inaccuracies caused by temperature variations and/or long-term drift. The benefit of running SPC is that is optimizes the oscilloscope's …
Идентификатор часто задаваемых вопросов60041
How do I utilize the math channel feature on a DPO/MSO/MDO3000 or DPO/MSO/MDO4000 Series oscilloscope?
There are three main functionalities on the Math button on this scope. They range from Dual Waveform Math, FFT (Fast Fourier Transform), and Advance Math. These three functionalities have a range of abilities and are explained in this short YouTube …
Идентификатор часто задаваемых вопросов64656
Is there a mictor adapter for the P6616 (logic probe for MSO5000B, MSO4000B, and MDO4000C + MDO4MSO) or P6516 (logic probe for the MSO4000 Series) or the P6316 (logic probe for MSO2000, MSO3000, MDO3000 + MDO3MSO Series)?
A mictor adapter is available from our partner Nexus Technologies. Use the mictor adapter NEX-HD2HEADER http://www.nexustechnology.com/products/laAccessories/hd2header/  
Идентификатор часто задаваемых вопросов59716
Why do I see 16 flat lines for the MSO digital logic inputs when the same signals are displayed properly on the analog channels and all channels are setup for valid trigger threshold levels?
A common mistake for some, we first recommend verifing that the front panel MSO digital probe is properly connected by squeezing the probe's side latch buttons to un-plug, remove the probe then re-insert the probe label side up into the front panel …
Идентификатор часто задаваемых вопросов60251
How do I mount a network drive on my MDO3000 or MDO4000C oscilloscope?
This procedure also applies to the DPO/MSO/MDO4000/4000B series oscilloscopes.  Note: This Mount a network drive will not work with a direct (peer-to-peer) connection. Must go through your local DNS server. To begin, press the “Menu” button in the …
Идентификатор часто задаваемых вопросов66201
How do I reduce noise on signals using an oscilloscope?
There are many methods to reduce many types of noise on a signal. Tektronix oscilloscopes can do this through bandwidth limiting the scope input, averaging your signal, changing the sampling method to hi-resolution mode, and more. This video …
Идентификатор часто задаваемых вопросов64706
What is TekVISA and how can I use it to communicate with and control my instrument?
VISA is an acronym that stands for Virtual Instrument Software Architecture. In a nutshell, VISA handles the communications between your computer’s OS and the instrument.  You may be familiar with TekVISA, which is Tektronix’s own brand of VISA …
Идентификатор часто задаваемых вопросов69176
How do I setup my DPO/MSO4000B to NI Signal Express?
Please click on video below.  
Идентификатор часто задаваемых вопросов64606
What is the difference between the P6139A and the P6139B?
From a specifications perspective, the probes are identical. Both are 500 MHz, 10X passive probes. The P6139B can be used on oscilloscopes that shipped with the P6139A.From a mechanical perspective, there are some differences:- Sharper tip- Ground …
Идентификатор часто задаваемых вопросов64441
How do I connect an SMA male output to Oscilloscopes with TekVPI BNC inputs?
Use a Tektronix part number 015-0572-XX SMA female to BNC male adapter. This adapter will plug onto the BNC on the front of the scope and connect to a SMA cable. For more questions please press the "Contact Us" button on the right of the screen.   
Идентификатор часто задаваемых вопросов63516
How do I use TekVISA to send commands to my instrument?
TekVISA Download Link:TEKVISA CONNECTIVITY SOFTWARE In order to communicate with and control the scope, you can use OpenChoice Talker-Listener. Back on the Application and Utilities panel, click on OpenChoice Talker Listener and click Start …
Идентификатор часто задаваемых вопросов69181
How do I set up a USB bus decode?
First you must have the USB module or option key that enables USB decoding for your scope as well as proper probes. For help finding the right probe use our probe selector tool. When you go into the bus option you must select USB and then make sure …
Идентификатор часто задаваемых вопросов64726
What rackmount does my scope use?
Oscilloscope Family Rackmount TDS1000/TDS2000 RM2000 TDS1000B/TDS2000B/TDS2000C RM2000B TPS2000/TPS2000B No Rackmount - Strap hanger 343-1689 …
Идентификатор часто задаваемых вопросов64571
How do I download and install the 30-day trial version of NI LabVIEW SignalExpress Tektronix Edition?
Note: NI LabVIEW SignalExpress Tektronix Edition is no longer offered by Tektronix. This FAQ is "historical only".National Instruments SignalExpress Tektronix Edition is a measurement automation tool that allows SignalExpress to control a Tektronix …
Идентификатор часто задаваемых вопросов66221
How do I utilize the measurement features on a DPO/MSO/MDO3000 and DPO/MSO/MDO4000 Series oscilloscope?
The Measurements are the same as the DPO/MSO2000 Series scopes. By going into the measurement menu you can add and remove up to 4 measurements. You can gate the measurements which allows you to only measure the part of the captured waveform that you …
Идентификатор часто задаваемых вопросов64651
How do I set up an Ethernet bus decode?
Make sure your setup is prepared to decode, that you have the needed probes, scope options, test boards, etc. Once you have the options it's important to know how to use the options and probe your signal. To setup Ethernet bus decoding, turn on your …
Идентификатор часто задаваемых вопросов64731
How do I Set Up a LIN serial Bus decode?
For doing Local Interconnect Network (LIN) bus decode Tektronix recommends using a DPO/MSO/MDO series oscilloscope. This feature can be purchased as a module or option key on any of these types of oscilloscopes. Start by turning it on the bus channel …
Идентификатор часто задаваемых вопросов64781
When should I use MagniVu on my oscilloscope?
MagniVu allows you to have higher resolution to accurately determine edge placement on your digital data. It helps you to make precise timing measurements on digital edges. On the MSO/MDO4000/B/C and MSO5000/B Series, you can see up to 32 times more …
Идентификатор часто задаваемых вопросов63886
Why Should My Signal Fit Within The Screen Of My Tektronix Oscilloscope?
Scaling your signal to fit within the screen will remove signal distortion caused by clipping. Clipping is caused by exceeding the limits of the instrument's input. Tektronix's digital oscilloscopes are designed such that each division is 25 digital …
Идентификатор часто задаваемых вопросов60306
The data sheet for my oscilloscope says that the vertical input sensitivity is 1 mV/div to 10 V/div in 1 MΩ mode. But I turn the Vertical Scale control fully clockwise and I can only get down to 10 mV/div. What am I doing wrong?
You probably aren't doing anything wrong. But you do have a 10X probe attached to that channel, right? The 1 mV/div specs relate to the oscilloscope inputs. If the signal’s source impedance is relatively low (<< 1 MOhm), the signal’s frequency is …
Идентификатор часто задаваемых вопросов58571
Will the P6516 Logic Probe work on my MSO4000B, MDO4000B and MDO4000C Series oscilloscopes?
The P6516 logic probe was only used with the original MSO4000 series. For the subsequent MSO4000B, MDO4000B and MDO4000C Series oscilloscopes, the P6516 was replaced by the P6616 logic probe. The P6616 logic probe will not work on the original …
Идентификатор часто задаваемых вопросов246206
What is the difference between Position and Offset on an oscilloscope?
To answer this first you need to understand the layout of how your waveform trace is displayed. On your oscilloscope you generally will see either 8 or 10 divisions vertically on the screen. Along the left side of the screen you will see a marker …
Идентификатор часто задаваемых вопросов247211
Which probes are compatible with oscilloscopes with the TekVPI probe interface?
There are a couple different types of TekVPI interfaces, one with a notch and one without. The notch was implemented later and was put in place because the front end was designed differently and communicates uniquely with those types of probes …
Идентификатор часто задаваемых вопросов56226
What cart does my scope use?
Below are the Instrument Carts that can be purchased from Tektronix.                                         K4000                                                                             K420                              K475 More information can …
Идентификатор часто задаваемых вопросов64561
What probe interface does my oscilloscope have?
Oscilloscope series Probe interface CSA7000/CSA7000B TekConnect DPO2000 TekVPI DPO3000 …
Идентификатор часто задаваемых вопросов64251
Can the P6139B be used on scopes that shipped with a P6139A? What is the difference between the P6139A and the P6139B?
From a specifications perspective, the probes are identical. Both are 500 MHz, 10X passive probes. The P6139B can be used on oscilloscopes that shipped with the P6139A. From a mechanical perspective, there are some differences: - Sharper tip …
Идентификатор часто задаваемых вопросов58111
How can I increase the measurement accuracy using automated measurements vs cursors?
While Cursors are quick and easy at approximating measurements, using the automated measurements can give you a much better and accurate measurement results. Here are some techniques to be successful in making accurate measurements. Always use …
Идентификатор часто задаваемых вопросов62606
What are the differences between the MSO4000B/DPO4000B Series and the MSO4000/DPO4000 Series?
Please see the attached PDF for the differences between the MSO4000B/DPO4000B and the MSO4000/DPO4000. For information comparing the MSO/DPO4000B to the MDO4000/B/C Series please use this FAQ >> CLICK HERE
Идентификатор часто задаваемых вопросов58621
How do I save and load a reference waveform to a DPO/MSO3000 series oscilloscope?
This Video will explain how to setup, save and load a reference waveform. It can be done through a USB flash drive or by internal memory. This method for using reference waveforms can be applied to all MSO/DPO2000, MSO/DPO3000, MSO/DPO/MDO4000 …
Идентификатор часто задаваемых вопросов64641
How do I set up a RS232 bus decode?
The procedure to set up a RS232 bus decode and trigger is simple once you understand the basics. First you need to have the correct module or scope option. Second make sure your signal is on screen and taking up as much of the screen as possible with …
Идентификатор часто задаваемых вопросов64761
How do I use the Save and Recall functionality of the MDO4000 series oscilloscope?
To save a screen image, go to the Save/Recall menu at the bottom of the scope. From there select the Save Screen Image softkey. This will pop up a new window with saving options. Saving a screen image requires an external memory device, such as a USB …
Идентификатор часто задаваемых вопросов69156
How do I Set up a Military Standard 1553 serial bus decode?
For doing Military Standard 1553 bus decode Tektronix recommends using a DPO/MSO/MDO 2000 or higher series oscilloscope. This feature can be purchased as a module or option key on any of these types of oscilloscopes. Start by turning it on the bus …
Идентификатор часто задаваемых вопросов64776
Do the existing MSO/DPO/MDO4000/B Series application modules work with the MDO4000C?
Yes, almost all work from all legacy MSO/DPO/MDO4000/B series scopes. The only one that has some requirements is the MDO4TRIG which requires a spectrum analyzer option MDO4SA3 or MDO4SA6 be installed on your MDO4000C before RF triggering capabilities …
Идентификатор часто задаваемых вопросов72146
My Tektronix oscilloscope uses the Linux operating system.  Where do I get a copy of the linux open source code as stated in the GNU Lesser General Public License notice?
For our Linux based instruments or programs licensed under the “GNU General Public License (GPL) or Lesser GNU General Public License (LGPL)” the complete corresponding sources are available. You can order a complete machine-readable copy of the …
Идентификатор часто задаваемых вопросов64866
How do I utilize the XY display feature on a DPO/MSO/MDO4000 Series oscilloscope?
The XY display format can be used to measure the phase relationship between two or more synchronous signals. This measurement technique involves inputting one signal into the vertical system as usual and then another signal into the horizontal system …
Идентификатор часто задаваемых вопросов64666
What are some of the benefits of the TekVPI probe interface?
The biggest benefits of the TekVPI™ probe interface are versatility and ease of use. Oscilloscopes with TekVPI interface support a wide range of probes including TekVPI probes, BNC and TekProbe-BNC Level 1 probes, and TekProbe-BNC Level 2 probes …
Идентификатор часто задаваемых вопросов56016
How do I configure the LAN settings on an MDO4000C series oscilloscope?
This procedure also applies to the DPO/MSO/MDO4000B series oscilloscopes. As it stands now, all 4000 series scopes  require a live network connection  be made on the scope in order to set and save LAN settings. If the scope does not have a network …
Идентификатор часто задаваемых вопросов66236
How can I change the TekVISA Instrument descriptor “device name” used to identify the oscilloscopes to which I routinely connect?
Open TekVISA V4.0.0+ OpenChoice Instrument Manager by selecting Start -> All Programs -> TekVISA ->  OpenChoice Instrument Manager.Select (highlight) the Instrument descriptor listed in the Instruments list for the connected Oscilloscope.Click the …
Идентификатор часто задаваемых вопросов66181
How do I clear my memory using TekSecure on a MSO/DPO/MDO4000 Series oscilloscope?
This procedure for clearing the memory on oscilloscope can be applied to the DPO/MSO/MDO4000, DPO/MSO3000 and DPO/MSO2000 Series oscilloscope families. By clearing the memory you will lose all saved reference waveforms, saved setups and all other …
Идентификатор часто задаваемых вопросов64686
Can the P6316, P6516, or P6616 logic probes be used interchangeably?
The simple answer is no they can't be used interchangeably. The front end of the logic channels are different so different logic probes are needed between the scopes.   For MSO2000/B, MSO3000, and MDO3000 Series oscilloscopes, only the P6316 logic …
Идентификатор часто задаваемых вопросов59166
How do I erase and declassify an MSO/DPO2000, MSO/DPO/MDO3000, and MSO/DPO/MDO4000 Series oscilloscope?
This example will show you how to declassify the MDO4000/B/C Series oscilloscope. This procedure also applies to the MSO/DPO4000/B, MSO/DPO/MDO3000, and the MSO/DPO2000/B series of oscilloscope.The first step in the declassification process is …
Идентификатор часто задаваемых вопросов66231
I could not find any information regarding the increase in bits in resolution for HiRes mode. Is there any information available?
The increase in bits in resolution depends on the decimation ratio.  The decimation ratio can be determined as follows:D = MFs / FsMFs is the maximum non-interleaved sampling frequency of the scope.  For example: 5 GS/s for the DPO4104B or 2.5 GS/s …
Идентификатор часто задаваемых вопросов55421
Programing - How do I get a Screen Capture from DPO4000 scope using Python?
There are a few things that are needed for programming with an oscilloscope. First it's important to have a copy of your oscilloscopes Programmers manual. This can be found be searching for manuals on Tek.com and specifying Programmers manual in the …
Идентификатор часто задаваемых вопросов64791
How do I use the programmer manual for my instrument?
TekVISA Download Link: TEKVISA CONNECTIVITY SOFTWARE Hello and welcome to Tektronix, today I’m presenting the last part in the 3-part series on using TekVISA. I’ll be giving a basic overview of programmer manuals and how to use them to find the …
Идентификатор часто задаваемых вопросов69186
How Do I Set Up a Parallel Bus Decode?
For doing Parallel Bus decode Tektronix recommends using a MSO or MDO + MSO option Series oscilloscopes. This feature comes standard in the Bus menu and can be used in a variety of ways. Start by turning it on, selecting the channel and setting your …
Идентификатор часто задаваемых вопросов64771
What is aliasing and how do I detect it and fix it on my oscilloscope?
Aliasing is basically a form of under sampling and what is displayed on the scopes is an indistinguishable waveform. The under sampled waveform is then contstructed to look like a slower frequency waveform or a flat line in the case of the sample …
Идентификатор часто задаваемых вопросов64691
When running SPC (signal path compensation) on my oscilloscope, I get the message that SPC failed.  What does failing SPC indicate?
When an oscilloscope says SPC failed, 99.9 percent of the time it is a hardware failure that will need repair.  A few things you can do before sending in for repair: Make sure all inputs (probes and cables) are removed from all the channel inputs …
Идентификатор часто задаваемых вопросов59621
I cannot see my signal on the Oscilloscope. What can I do?
You have many options to help diagnose this issue, below are a few suggestions to get started. If you find yourself needing more help, please connect with our Technical Support Center. You can get started by pressing the "Contact Us" button on the …
Идентификатор часто задаваемых вопросов63686
Companies such as National Instruments and LeCroy sell USB-to-GPIB adapters. How do their adapters compare to the TEK-USB-488?
The products from National Instruments (GPIB-USB-B or GPIB-USB-HS) and LeCroy (WS-GPIB) are USB host to GPIB device adapter. These would be used for instruments that have a GPIB interface with controllers that have a USB port. The TEK-USB-488 was …
Идентификатор часто задаваемых вопросов56456
Programing - How to get and plot a waveform from DPO/MSO/MDO4000 Series scope in Python
There are a few things that are needed for programming with an oscilloscope. First it's important to have a copy of your oscilloscopes Programmers manual. This can be found be searching for manuals on Tek.com and specifying Programmers manual in the …
Идентификатор часто задаваемых вопросов64796
I downloaded and Installed OpenChoice Desktop, but it doesn't recognize my scope.
Refer to the Prerequisites.txt file available to download on the same page for OpenChoice desktop. Make sure you have all the prerequisites specified.    Prerequisites 1. PC equipped with  Microsoft Windows 7 32 Bit and 64 Bit OS, Windows 8.1 32 Bit …
Идентификатор часто задаваемых вопросов474266
Why does the Tkdpo2k3k4k_ReadWaveform() function in the Tkdpo2k3k4k IVI-C driver time out every time I call it when I am connected to the instrument via Ethernet? The function call works fine over USB, but over Ethernet it always times out.
The Tkdpo2k3k4k_ReadWaveform() function makes use of the Service Request Event in VISA so the scope can notify the driver when it has completed its acquisition and the waveform data is ready to be fetched as opposed to the driver polling the scope …
Идентификатор часто задаваемых вопросов72221
MDO4000C, MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes

This manual explains the use of commands for remotely controlling youroscilloscope. With this information, you can write computer programs toperform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.


Номер по каталогу: 077051009
Электронное руководство по программированию
Tektronix Demo 3 Board Instruction Manual
Demo 3 Board Instruction Manual

This document describes the operation of the Tektronix Demo 3 Board. The Demo 3 board provides signals to demonstrate key Tektronix instrument features.


Номер по каталогу: 071286202
Тренинг/обучающие материалы
MSO4000B and DPO4000B Series
Digital Phosphor OscilloscopesSpecifications and Performance Verification

Revision B. This manual contains the specifications and the performance verification procedures for the MSO4000B and DPO4000B Series oscilloscopes.


Номер по каталогу: 077050903
Проверка рабочих характеристик
MSO4000B and DPO4000B Series
Digital Phosphor Oscilloscopes

This MSO4000B and DPO4000B series user manual explains how to operate the oscilloscope and includes installation procedures. It also provides information about features, functions, and applications.


Номер по каталогу: 071281004
Основной потребитель
MDO4000C, MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes

This manual explains the use of commands for remotely controlling youroscilloscope. With this information, you can write computer programs toperform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.


Номер по каталогу: 077051007
Электронное руководство по программированию
KickStart Instrument Control Software Version 2.2.0 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the …

Номер по каталогу: KICKSTART-2.2.0
Application (Предварительные установки > Приложение)
KickStart Instrument Control Software Version 2.1.1 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the …

Номер по каталогу: KICKSTART-2.1.1
Application (Предварительные установки > Приложение)
TEKVISA Connectivity Software - V4.2.0
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol.When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various …

Номер по каталогу: 066093812
Драйвер
DPO2000, MSO2000, DPO3000 and DPO4000, MSO3000 and MSO4000, MDO3000 and MDO4000 and MDO3 IVI Driver - V1.5
The Tektronix MSO/DPO2000, MDO/MSO/DPO3000, MDO/MSO/DPO4000 and MDO3 IVI Driver is an IVI class-compliant driver. It complies with Scope Class specifications (IVI-4.1) as defined by the IVI foundation. An IVI class-compliant specific driver for an …

Номер по каталогу: 066133104
Драйвер
KickStart Instrument Control Software Version 2.1.0 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the …

Номер по каталогу: KICKSTART-2.1.0
Application (Предварительные установки > Приложение)
TEKVISA CONNECTIVITY SOFTWARE - V4.1.1
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol.When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various …

Номер по каталогу: 066093811
Драйвер
MSO4000B, DPO4000B Firmware - V3.22
This firmware is an upgrade for all MSO/DPO4000B Series oscilloscopes.

Номер по каталогу: 063447007
Микропрограммное обеспечение
Tektronix Openchoice Desktop Application TDSPCS1 - v2.6
The Tektronix OpenChoice Desktop free application lets you capture oscilloscope screen images, waveform data, and settings from a Microsoft Windows computer. After installing the software, refer to the section “Connecting to a PC” in your …

Номер по каталогу: 066093914
Utility
MSO4000B, DPO4000B Firmware, V3.20
This firmware is an upgrade for all MSO/DPO4000B Series oscilloscopes.

Номер по каталогу: 063447006
Микропрограммное обеспечение
How to Minimize Probe Loading with Low Capacitance Probes
Probing a circuit always has some impact on signals. Probe loading changes the signal being probed and can cause measurement problems or can even cause a circuit to perform differently. Reducing capacitive loading can help minimize these effects. In …

Номер публикации: 51W-26294-6
Примечание по применению
Oscilloscope Selection Guide
From basic signal-checking to high-performance analysis, this selection guide gives an overview of the complete range of oscilloscopes from Tektronix. Comparison tables give high-level specifications and features, and indicate the major differences …

Номер публикации: 46W-31080-7
Руководство по выбору оборудования
Making Accurate Current Measurements on Power Supplies with Oscilloscopes
Accurately measuring current with oscilloscopes is essential for power supply design and general electronics. Learn how to measure current using shunt resistors and voltage probes, and how to use clamp-on current probes with your oscilloscope. Get …

Номер публикации: 51W-60171-2
Примечание по применению
Test methodologies for high-speed serial designs
Статья о приборе
Power Supply Measurement and Analysis Primer
A power supply is a component, subsystem, or system that converts electrical power from one form to another; commonly from alternating current (AC) utility power to direct current (DC) power. The proper operation of electronic devices ranging from …

Номер публикации: 55T-18412-6
Начальное руководство
Testing a New Switch Mode Power Supply Design Poster
Get a quick overview of the key measurements for verifying a new switch mode power supply (SMPS) design.  This poster shows key measurements, from verifying your prototype during initial startup, to optimizing switching loss and magnetic losses, to …

Номер публикации: 46W-60156-0
Объявление
TekScope Anywhere, TM
TekScope Anywhere™ brings the power of the oscilloscope analysis environment to the PC. Your workflow becomes more flexible because you can now perform complex analysis tasks including timing, eye, and jitter analysis outside of the lab. Waveform …

Номер по каталогу: 066177100
Application (Предварительные установки > Приложение)
MSO4000B, DPO4000B Firmware, V3.18
This firmware is an upgrade for all MSO/DPO4000B Series oscilloscopes.

Номер по каталогу: 063447005
Микропрограммное обеспечение
Tektronix Toolbars for Microsoft Office, V4.0.4
Tektronix Toolbars for Microsoft Office v4.0.4 provide toolbars (add-ins) for Microsoft Excel and Microsoft Word.This version of Toolbars requires OpenChoice TekVISA v4.0.0 or higher be preinstalled on the PC or Windows based Oscilloscope.The Toolbar …

Номер по каталогу: 066133202
Utility
MSO4000B, DPO4000B Firmware, V3.16
This firmware is an upgrade for all MSO/DPO4000B Series oscilloscopes.

Номер по каталогу: 063447004
Микропрограммное обеспечение
TEKVISA CONNECTIVITY SOFTWARE, V4.0.4
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol. When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various …

Номер по каталогу: 066093809
Драйвер
MSO4000B, DPO4000B FIRMWARE, V2.96
This firmware is an upgrade for all MSO/DPO4000B Series oscilloscopes.

Номер по каталогу: 063447002
Микропрограммное обеспечение
MSO4000B, DPO4000B FIRMWARE, V2.90
This firmware is an upgrade for all MSO/DPO4000B Series oscilloscopes.

Номер по каталогу: 063447001
Микропрограммное обеспечение
DPO2000, DPO3000, DPO4000 IVI Driver
The Tektronix DPO2000, DPO3000, DPO4000 IVI Driver is an IVI class-compliant driver. It complies with Scope Class specifications (IVI-4.1) as defined by the IVI foundation. An IVI class-compliant specific driver for an oscilloscope exports the API …

Номер по каталогу: 066133101
Драйвер
DPO4000B AND MSO4000B FIRMWARE V2.52
This firmware is an upgrade for all DPO4000B and MSO4000B Series oscilloscopes.

Номер по каталогу: 063432911
Микропрограммное обеспечение
DPO4000 AND MSO4000 FIRMWARE V2.62
This firmware is an upgrade for all DPO4000 and MSO4000 Series oscilloscopes.

Номер по каталогу: 063397016
Микропрограммное обеспечение
USING MATLAB WITH MSO_DPO4000 AND MSO_DPO3000 SERIES OSCILLOSCOPES v1.0
MATLAB is a software environment and programming language that enables Tektronix oscilloscope users to acquire and analyze data, graphically visualize data, make custom measurements, generate reports, and develop automated applications. Perform …

Номер по каталогу: 066110000
Драйвер
Oscilloscope Combines Logic Analyzer With Ease Of Use For Better Debugging
Статья о приборе
Debugging a Mixed Signal Design with a Tektronix Mixed Signal Oscilloscope
A typical embedded systems design may incorporate various analog signals, high-speed and low-speed serial digital communication, microprocessor buses and more. This application note walks you through the debug of a mixed signal design with the …

Номер публикации: 3GK-20215-1
Примечание по применению
Hunting Noise Sources in Wireless Embedded Systems
In adding wireless capability to embedded systems, there are a number of issues typically encountered in the integration. In this application note you will find tips and techniques for hunting noise sources with the MDO4000 Series Mixed Domain …

Номер публикации: 48W-26920-0
Информационный бюллетень
iCub Robot Gets Battery Power with Help of Tektronix Oscilloscope, Voltage and Current Probes
Developers at the Istituto Italiano Di Tecnologia (IIT) needed to validate and troubleshoot a new battery backpack power supply system for the iCub robot, an open-source cognitive humanoid robot platform. This case study shows how IIT used the …

Номер публикации: 48W-31073-0
Анализ примеров
Serial Support Using Tektronix Oscilloscopes and Optional Software
Tektronix oscilloscopes offer a portfolio of optional analysis capabilities to simplify serial bus debug or compliance verification. This selection matrix shows which serial standards are supported by each of the oscilloscope series.

Номер публикации: 55W-29028-13
Руководство по выбору оборудования
Making MicroVolt Biomedical Measurements
Learn how paying attention to grounding, isolation, and probe shielding can produce very refined biomedical measurement, inexpensively.

Номер публикации: 48W-28061-0
Краткое техническое описание
Probing Techniques for Accurate Voltage Measurements on Power Converters with Oscilloscopes
Making oscilloscope voltage measurements on power supplies is fundamental, but not without challenges. Much is written on oscilloscopes, but probing techniques are often taken for granted. This application note focuses on probing and covers:Choosing …

Номер публикации: 51W-60161-3
Примечание по применению
Осциллографы: Основные принципы измерений
После прочтения этого учебного пособия неискушенный читатель сможет:■ ясно представлять себе как работает осциллограф;■ понять разницу между различными типами осциллографов;■ представлять себе, какие бывают формы электрических колебаний;■ детально …

Номер публикации: 03Z-8605-7
Начальное руководство
Your Guide to Selecting the Right Bench Oscilloscope
The Bench Selection Guide highlights the innovative and powerful features and benefits of the MSO /DPO Series. With up to 20 analog and digital channels, and automated serial and parallel bus analysis the MSO /DPO Series provides the feature-rich …

Номер публикации: 3GW-24014-1
Руководство по выбору оборудования
Wave Inspector® Navigation and Search: Simplifying Waveform Analysis
Modern digital oscilloscopes can capture massive amounts of data which must then be analyzed.  Discover how the Tektronix Wave Inspector® navigation and search capability gives you the tools to extract the answers you need fast and efficiently.

Номер публикации: 48T-19039-9
Примечание по применению
Capacitance and Inductance Measurements Using an Oscilloscope and a Function Generator
If you don't have an LCR meter in your lab, or you want to demonstrate the behavior of capacitors and inductors under sinusoidal stimulus, an oscilloscope and a function generator can help you to do a simple, transparent impedance measurement. You …

Номер публикации: 75W-28152-0
Примечание по применению
Smiths Detection Relies on Tektronix to Take the Trouble out of Troubleshooting
A team of engineers at Smith Detection needed to quickly, efficiently and accurately identify and resolve problems during the development of complex handheld devices. Learn how Smith Detection engineers used Tektronix bench instruments to identify a …

Номер публикации: 48W-24397-0
Краткое техническое описание
Debugging a Mixed Signal Design with a Tektronix Mixed Signal Oscilloscope
A typical embedded systems design may incorporate various analog signals, high-speed and low-speed serial digital communication, microprocessor buses and more. This application note walks you through the debug of a mixed signal design with the …

Номер публикации: 3GW-20215-6
Примечание по применению
Свидетельство DPO4000B-L - MSO4000B-L
Свидетельство об утверждении типа средств измерений РФ 
Сертификат на русском языке
10 Reasons Why You Have Never Seen a Mixed Signal Oscilloscope Like This
Learn more about all the innovative user-friendly features on the MSO4000 Series that have been designed to make your work easier.

Номер публикации: 3GT-20214-0
Брошюра
MDO/MSO/DPO4000B Series vs. Agilent MSO/DSO-X 4000A Series
Side-by-side comparison on important features like serial triggering and decode, waveform navigation and search, waveform capture rate, digital debug with MSO, and more.

Номер публикации: 3GW-29111-2
Конкурентоспособный
MDO4000B Series vs. Agilent/Keysight MSOX4000A Series
When comparing oscilloscopes, check the details of the operation and look for “hidden” costs that prevent you from getting the versatility in performance you need to complete the wide-variety of fundamental measurement challenges you have today and …

Номер публикации: 48W-30246-0
Конкурентоспособный
Tektronix MSO/DPO4000 Series vs. LeCroy WaveRunner Xi Fact Sheet
Side-by-side comparison on important features like serial triggering and decode, waveform navigation and search, and waveform capture rate.

Номер публикации: 48W-22679-3
Конкурентоспособный
Tektronix MSO/DPO4000 Series vs. LeCroy WaveSurfer XS Fact Sheet
Side-by-side comparison on important features like serial triggering and decode, waveform navigation and search, and waveform capture rate.

Номер публикации: 48W-22680-3
Конкурентоспособный
Tek oscilloscopes catch analog and digital signals
Статья о приборе
Tektronix MSO4000 Mixed Signal Oscilloscopes Win 2008 EDN China Innovation Award
Награда
Tektronix MSO4000 Series vs. LeCroy MS-500 Mixed Signal Solution Fact Sheet
Side-by-side comparison on important features like display size, searching on analog and digital data, and setup and hold triggering.

Номер публикации: 3GK-20891-0
Конкурентоспособный
Tektronix Adds Support for Automated APCO P25 Transmitter Compliance Testing
Also Releases a Series of Enhancements, Upgrades for Real-time Spectrum Analyzers Including Noise Figure and Gain Measurement CapabilityBEAVERTON, Ore., July 29, 2014 - Tektronix, Inc., a leading worldwide provider of test, measurement and monitoring …
Информационный выпуск
Tektronix MSOs Set Performance Benchmarks
Статья о приборе
Tektronix MSO4000 Series vs. LeCroy MS-500 Probe Fact Sheet
The Tektronix MSO4000 Series Mixed Signal Oscilloscope with P6516 digital probe, go head-to-head with the LeCroy MS-500 probe in this insightful product comparison brief. See side-by-side comparisons on size, flexible probing, and other key …

Номер публикации: 3GW-20891-0
Конкурентоспособный
Tektronix: 53% Faster for Digital Debug
The Digital Debug Research Study by Hansa GCR set out to find the best oscilloscope for debugging digital signals. In their quest, Hansa GCR challenged engineers to compare 3 scopes for this everyday engineering task. Watch this five-minute video to …
Конкурентоспособный
Tektronix MSO/DPO4000 Series vs. Agilent 5000A+ 6000A+ and 7000A Fact Sheet
Side-by-side comparison on important features like serial triggering and decode, waveform navigation and search, and record length.

Номер публикации: 3GW-21844-6
Конкурентоспособный
Product Catalog 2012 (Test&Measurement Solutions)
Данный каталог состоит из 51 страницы и содержит информацию об основных приборах, приложениях, также в нем Вы найдете таблицы с указанием полного ассортимента осциллографов, логических анализаторов, генераторов сигналов, анализаторов спектра …

Номер публикации: 49W-19265-11
Руководство по выбору оборудования
Bench Products 2012 (Test&Measurement Solutions)
На 16 страницах каталога предложены детали и технические характеристики настольных приборов Tektronix, включая: основные и настольные осциллографы, цифровые мультиметры, источники питания, частотомеры и генераторы сигналов.

Номер публикации: 48T-25025-8
Руководство по выбору оборудования
Portable Scopes Designed for Embedded Design and Debug
Статья о приборе
Power Supply Measurement and Analysis with Bench Oscilloscopes
Today’s power supplies are driving to a level of efficiency never seen before, requiring design engineers to perform specialized power measurements that are time-consuming and complex. Learn how using a Tektronix Bench Oscilloscopes provides fast …

Номер публикации: 3GZ-23612-6
Примечание по применению
Introduction to Video Measurements
In this application note, we demonstrate using a MSO/DPO5000, MDO/MSO/DPO4000 and MDO/MSO/DPO3000 Series Oscilloscope to make a variety of video measurements that are common in standard and high definition systems.

Номер публикации: 3GW-20975-2
Примечание по применению
3000 X-Series vs. MSO/DPO4000B Series True Cost of Your Scope
Tektronix bench oscilloscopes are packed with innovative features to help you get your job done faster, built right into the scope. And, with a comprehensive set of probes and accessories included standard, you can start testing right out of the box …

Номер публикации: 3GW-27919-0
Конкурентоспособный
Debugging Serial Buses in Embedded System Designs
Find out how the protocol trigger, decode and search capabilities of the popular MSO and DPO Series oscilloscopes solve serial bus integration and debug challenges of many buses such as I2C, SPI , USB, RS-232/422/485/UART, CAN, LIN, FlexRay, Ethernet …

Номер публикации: 48W-19040-21
Примечание по применению
Digital Debugging Tips Using a Mixed Signal Oscilloscope
This application note provided useful information for verifying and debugging with a Mixed Signal Oscilloscope (MSO) complex designs that may include analog and digital signals and multiple buses.

Номер публикации: 3GT-24008-4
Примечание по применению
Embedded-design MSOs pack all test tools in one box
Статья о приборе
Свидетельство DPO4000B-MSO4000B
Свидетельство об утверждении типа средств измерений РФ
Сертификат на русском языке
MSO/DPO4000 & MSO/DPO3000 Series vs. LeCroy MS-500 Mixed Signal Solution
Side-by-side comparison on important features like display size, searching on analog and digital data, and setup and hold triggering.

Номер публикации: 3GT-24011-0
Конкурентоспособный
MSO/DPO4000 vs. Agilent MSO7000B Fact Sheet
Side-by-side comparison on important features like serial triggering and decode, waveform navigation and search, waveform capture rate, digital debug with MSO, and more.

Номер публикации: 48T-25674-0
Конкурентоспособный
MSO/DPO4000B Series vs. Agilent MSO/DSO3000 X-Series
Side-by-side comparison on important features like serial triggering and decode, measurements and waveform math, digital debug with MSO, and more.

Номер публикации: 48W-27796-1
Конкурентоспособный
REVIEW: Cost-effective scopes time-correlate analog+ digital signals
Статья о приборе
MSO/DPO4000 Series vs. Yokogawa DLM2000 Series
Side-by-side comparison on important features like serial triggering and decode, waveform navigation and search, user-experience, digital debug with a MSO and more.

Номер публикации: 3GW-24237-1
Конкурентоспособный
Measuring Power Supply Switching Loss with an Oscilloscope
Losses due to dissipation in switching devices such as MOSFET's and IGBT's contribute significantly to the overall losses in switch mode power supplies.  This application note explains how to measure switching loss and conduction loss in power supply …

Номер публикации: 46W-60010-3
Примечание по применению
MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes Programmer Manual

This manual explains the use of commands for remotely controlling your oscilloscope. With this information, you can write computer programs to perform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.
Номер по каталогу: 077051006
Электронное руководство по программированию
MDO4000B, MDO4000, MSO4000B and DPO4000B Series
Digital Oscilloscopes Programmer Manual

This manual explains the use of commands for remotely controlling your oscilloscope. With this information, you can write computer programs to perform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.
Номер по каталогу: 077051005
Электронное руководство по программированию
RMD5000
Tektronix DPO & MSO 4000B Series and DPO & MSO5000/B Series Rackmount Kit Instructions

These instructions describe the installation of the rackmount kit to your standard bench-top instrument.
Номер по каталогу: 075102002
Инструкции по установке на объекте
Серии MSO4000B и DPO4000B Руководство по эксплуатации
Цифровые люминесцентные осциллографы User Manual

В этом руководстве по эксплуатации приборов серий MSO4000B и DPO4000B объясняется, как работает осциллограф, и приводятся процедуры установки. В нем также содержится информация о возможностях, функциях и приложениях.
Номер по каталогу: 071282003
Основной потребитель
MSO4000B and DPO4000B Series
Digital Phosphor Oscilloscopes Service Manual

This document provides information for technicians to maintain or service a product. Information is given to the module level, and may include product care and cleaning tips, troubleshooting information, adjustments, and how to replace parts.
Номер по каталогу: 077051202
Обслуживание
MSO4000B and DPO4000B Series and Application Modules
Declassification and Security Instructions

If you have data security concerns, this document helps you to sanitize or remove memory devices from the Tektronix MSO4000B Series and DPO4000B Series Digital Phosphor Oscilloscopes.
Номер по каталогу: 077051101
Исключение из классификации
MDO4000, MSO4000B and DPO4000B Series
Digital Oscilloscopes Programmer Manual

This manual explains the use of commands for remotely controlling your oscilloscope. With this information, you can write computer programs to perform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.
Номер по каталогу: 077051003
Электронное руководство по программированию
MSO4000B and DPO4000B Series
Digital Phosphor Oscilloscopes Service Manual

This document provides information for technicians to maintain or service a product. Information is given to the module level, and may include product care and cleaning tips, troubleshooting information, adjustments, and how to replace parts.
Номер по каталогу: 077051201
Обслуживание
MSO4000B and DPO4000B Series
Digital Phosphor Oscilloscopes User Manual

This MSO4000B and DPO4000B series user manual explains how to operate the oscilloscope and includes installation procedures. It also provides information about features, functions, and applications.
Номер по каталогу: 071281002
Основной потребитель
Read This First
Download the Latest IVI Drivers Read This First

This document is targeted to product users and explains installation procedures.
Номер по каталогу: 061438100
Примечания к выпуску
MDO4000, MSO4000B and DPO4000B Series
Digital Oscilloscopes Programmer Manual

This manual explains the use of commands for remotely controlling your oscilloscope. With this information, you can write computer programs to perform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.
Номер по каталогу: 077051002
Электронное руководство по программированию
MSO4000B and DPO4000B Series
Digital Phosphor Oscilloscopes Specifications and Performance Verification Technical Reference

This manual contains the specifications and the performance verification procedures for the MSO4000B and DPO4000B Series oscilloscopes.
Номер по каталогу: 077050901
Проверка рабочих характеристик
HCTEK54
Transit Case Instructions

This document provides information about the features and using the HCTEK54 transit case.
Номер по каталогу: 071282800
User (Предварительные установки > Пользователь)
MDO4000, MSO4000, MSO4000B, DPO4000, DPO4000B Series
Application Module Installation Manual

This document is targeted to product users and explains operation and/or installation procedures. It may also provide information about features and functions, applications and troubleshooting.
Номер по каталогу: 071213601
User (Предварительные установки > Пользователь)
Probe and Accessories
Pouch Installation Instructions

This document provides installation instructions for the MSO/DPO4000B probe and accessires pouch.
Номер по каталогу: 071283000
Инструкции по установке на объекте
This video shows how the MDO4000B linked to SignalVu-PC can be used to debug and test the integration of a WLAN module in an embedded design. The MDO4000B multi-domain capability helps with the …
8m 32s